- 您现在的位置：买卖IC网 > Sheet目录883 > SQE48T10120-NDA0G (Power-One)DC/DC EIGHTH BRICK
SQE48T10120 DC-DC Converter
36-75 VDC Input; 12 VDC @ 10A Output
Data Sheet
Protection Features
Input Undervoltage Lockout
Input undervoltage lockout is standard with this
converter. The converter will shut down when the
derating curves, or operation in abnormal conditions
such as system fan failure. Converter with the non-
latching option will automatically restart after it has
cooled to a safe operating temperature.
Safety Requirements
input voltage drops below a pre-determined voltage.
The converters
are safety approved to
The input voltage must be typically 34V for the
UL/CSA60950-1,
EN60950-1,
and IEC60950-1.
converter to turn on. Once the converter has been
turned on, it will shut off when the input voltage
drops typically below 32V. This feature is beneficial
in preventing deep discharging of batteries used in
telecom applications.
Output Overcurrent Protection (OCP)
The converter is protected against overcurrent or
short circuit conditions. Upon sensing an overcurrent
condition, the converter will switch to constant
current operation and thereby begin to reduce output
voltage.
If the converter is equipped with the special OCP
version designated by the suffix K in the part
number, the converter will shut down in
approximately 15ms after entering the constant
current mode of operation. The standard version
(suffix 0) will continue operating in the constant
current mode until the output voltage drops below
50% at which point the converter will shut down as
shown in Figure 13.
Once the converter has shut down, it will enter the
hiccup mode and attempt to restart approximately
every 200 ms with a typical 3-5% duty cycle as
shown in Figure 14. The attempted restart will
continue indefinitely until the overload or short circuit
Basic Insulation is provided between input and
output.
The converters have no internal fuse. If required, the
external fuse needs to be provided to protect the
converter from catastrophic failure. Refer to the
“Input Fuse Selection for DC/DC converters”
application note on www.power-one-com for proper
selection of the input fuse. Both input traces and the
chassis ground trace (if applicable) must be capable
of conducting a current of 1.5 times the value of the
fuse without opening. The fuse must not be placed
in the grounded input line.
Abnormal and component failure tests were
conducted with the input protected by a 5A fuse. If a
fuse rated greater than 5A is used, additional testing
may be required. To protect a group of converters
with a single fuse, the rating can be increased from
the recommended value above.
Electromagnetic Compatibility (EMC)
EMC requirements must be met at the end-product
system level, as no specific standards dedicated to
EMC characteristics of board mounted component
dc-dc converters exist. However, Power-One tests its
converters to several system level standards,
primary of which is the more stringent EN55022,
conditions are removed or the output voltage rises
Information
technology equipment
-
Radio
above 40-50% of its nominal value.
Once the output current is brought back into its
specified range, the converter automatically exits the
hiccup mode and continues normal operation
Output Overvoltage Protection (OVP)
The converter will shut down if the output voltage
across Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds
disturbance characteristics-Limits and methods of
measurement.
An effective internal LC differential filter significantly
reduces input reflected ripple current, and improves
EMC.
With the addition of a simple external filter, the
SQE48T10120 converter passes the requirements of
Class B conducted emissions per EN55022 and FCC
the threshold of the OVP circuitry. The OVP circuitry
requirements.
Please contact Power-One
contains its own reference, independent of the output
voltage regulation loop. Once the converter has shut
down, it will attempt to restart every 200 ms until the
OVP condition is removed.
Overtemperature Protection (OTP)
The converter will shut down under an
overtemperature condition to protect itself from
overheating caused by operation outside the thermal
Applications Engineering for details of this testing.
ZD-02075 Rev 1.1, 21-Jan-10
www.power-one.com
Page 7 of 13
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SQE48T20050-NGB0
DC/DC EIGHTH BRICK
SQE48T20120-NDABG
CONV DC-DC BUS 240W 12V 1/8 BRK
SQE48T30012-NGB0
DC/DC EIGHTH BRICK
SQE48T40015-NDA0
DC/DC EIGHTH BRICK
SQE48T40018-NDA0
DC/DC EIGHTH BRICK
SQE48T40025-NDA0
DC/DC EIGHTH BRICK
SQE48T50012-NDA0
DC/DC EIGHTH BRICK
SQL48T20033-NDA0G
CONV DC-DC 3.3V 20A 1/8 BRICK
相关代理商/技术参数
SQE48T10120-NDB0G
制造商:Power-One 功能描述:Conn Subminiature Cylindrical PIN 15 POS Crimp ST Wall Mount 15 Terminal 1 Port 制造商:Power-One 功能描述:- Bulk
SQE48T10120-PDA0G
功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
SQE48T20033－NGB0G
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 20A 8PIN - Bulk 制造商:Power-One 功能描述:Module DC-DC 1-OUT 3.3V 20A 8-Pin 1/8-Brick 制造商:Power-One 功能描述:DC/DC CONVERTER 3.3V 66W
SQE48T20033-NGBO
制造商:POWER-ONE INC 功能描述:PwrSup;DC-DC Converter;Out 3.3VDC;In 36 to 75VDC;Thru-Hole;Open-Frame;Switching
SQE48T20050-NDAK
制造商:Power-One 功能描述:SQE48T Series Single Output 5 V DC/DC Converter Power Supply
SQE48T20050-NDBKG
制造商:Power-One 功能描述:DC-DC CONVERTER, 36-75 VDC INPUT 5.0 VDC
SQE48T20050-NGA0
制造商:Power-One 功能描述:Module DC-DC 1-OUT 5V 20A 8-Pin 1/8-Brick 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 5V 20A 8PIN - Bulk
SQE48T20050-NGB0
功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: